MATERIAL SAFETY DATA SHEET Product Name: PRO-GARD 1000, Part A SECTION 1: IDENTIFICATION MANUFACTURER: LiquidConcrete, Inc. ADDRESS: P.O Box 16782, Seattle, WA 98116 PHONE: 1 (800) 201-9300 CHEMICAL NAME: Epoxy Resin COMMON NAME: PRO-GARD 1000, Part A CHEMICAL FAMILY: Modified Liquid Epoxy Resin SECTION 2: HAZARDOUS CHEMICALS H.M.I.S. RATING Health Flammability Reactivity 1 1 0 APPLICABLE EXPOSURE LIMITS CHEMICAL NAME/CAS # Reaction products of Epichlorohydrin and Bisphenol A / 25085-99-8 Cresyl Glycidyl Ether / 2210-79-9 CARCINOGENIC INGREDIENTS: N/A SECTION 3: HEALTH HAZARDS EYES: May cause eye irritation. SKIN: Prolonged or repeated exposure may cause skin irritation. May cause skin sensitization. SKIN ABSORPTION: A single prolonged skin exposure is not likely to result in absorption of harmful amount. The dermal LD50 is unknown. INGESTION: Single dose oral LD50 is unknown. Single dose oral toxicity is expected to be low. INHALATION: No guide for control established. Single exposure to vapors is not likely to be hazardous. ROUTES OF ENTRY: N/A MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: N/A SECTION 4: FIRST AID EYES: Irrigate immediately with water for at least 5 minutes. SKIN: Wash off in flowing water or shower. Remove contaminated clothing and wash before reuse. Use extra care with shoes. INGESTION: Induce vomiting if large amounts are ingested. % >70 <30 PEL-WISHA/OSHA none established none established TLV-ACGIH none established none established OTHER none established Revision Date: January 26, 2007 Page 1 of 4 Effective Date: January 26, 2007 MATERIAL SAFETY DATA SHEET Product Name: PRO-GARD 1000, Part A INHALATION: Remove to fresh air if effects occur. Consult medical. NOTE TO PHYSICIANS: No specific antidotes. Supportive care. Treatment based on judgement of the physician in response to reactions of the patient. SECTION 5: FIRE AND EXPLOSION DATA FLASH POINT (method used) >200º F (93º C) (Pensky-Martin Closed Cup) FLAMMABILITY LIMITS N/A LEL N/A UEL N/A EXTINGUISHING MEDIA: Foam, CO2, dry chemicals SPECIAL FIRE FIGHTING PROCEDURES: SPECIAL FIRE FIGHTING EQUIPMENT: Wear positive pressure self-contained breathing apparatus during fire fighting. UNUSUAL FIRE AND EXPLOSION HAZARDS: N/A HAZARDOUS DECOMPOSITION PRODUCTS: Under conditions of imperfect combustion and/or pyrolysis various phenolic compounds CO and/or CO2 may be evolved. HAZARDOUS POLYMERIZATION: Will not occur by itself, but masses of more than one pound of product plus an aliphatic amine will cause irreversible polymerization with heat build up. SECTION 6: ACCIDENTAL RELEASE MEASURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Soak up in non-reactive absorbent material or scrape up. The residue can be removed with hot, soapy water. Use of methylene chloride, acetone, or aromatic solvents in clean up poses a distinct hazard and therefore should be avoided. SECTION 7: HANDLING AND STORAGE N/A SECTION 8: PERSONAL PROTECTION AND EXPOSURE CONTROLS RESPIRATORY PROTECTION: N/A VENTILATION: LOCAL EXHAUST: Good room ventilation usually adequate for most operations. PROTECTIVE GLOVES: see below EYE PROTECTION: Safety glasses. OTHER PROTECTIVE EQUIPMENT: Clean, body covering clothing. In addition, rubber gloves, boots, aprons, gauntlets, and full face shield depending on the extent and severity of exposure likely. OTHER ENGINEERING CONTROL: N/A Revision Date: January 26, 2007 Page 2 of 4 Effective Date: January 26, 2007 MATERIAL SAFETY DATA SHEET Product Name: PRO-GARD 1000, Part A WORK PRACTICES: Practice caution and good personal cleanliness to avoid skin and eye contact. Avoid breathing vapors of heated material. HYGIENIC PRACTICES: N/A SECTION 9: TYPICAL PHYSICAL AND CHEMICAL PROPERTIES BOILING POINT (360º F) SPECIFIC GRAVITY (H20=1) 1.12-1.14 VAPOR PRESSURE (mmHG) N/A PERCENT NONVOLATILE BY VOLUME (100%) VAPOR DENSITY (AIR=1) N/A EVAPORATION RATE N/A SOLUBILITY: N/A APPEARANCE AND ODOR: Clear, light yellow, or pigmented. Faint epoxy odor. SECTION 10: STABILITY AND REACTIVITY STABILITY (CONDITIONS TO AVOID): Excessive heating over long periods of time degrade resin. Freezing may cause temporary haziness. INCOMPATIBILITIES: Strong oxidizing agents and nitrates. SECTION 11: TOXICOLOGICAL PROPERTIES N/A SECTION 12: ECOLOGICAL INFORMATION N/A SECTION 13: DISPOSAL INFORMATION WASTE DISPOSAL METHOD: Burn in adequate incinerator or bury in approved landfill. SECTION 14: TRANSPORT INFORMATION N/A SECTION 15: REGULATORY INFORMATION Revision Date: January 26, 2007 Page 3 of 4 Effective Date: January 26, 2007 MATERIAL SAFETY DATA SHEET Product Name: PRO-GARD 1000, Part A N/A SECTION 16: OTHER INFORMATION DISCLAIMER: The information contained herein is based on data believed to be accurate. However, no warranty is expressed or implied regarding the accuracy of these data or the results to be obtained from the use thereof. Recipients are advised to confirm in advance of need that the information is current, applicable, and suitable regarding all current regulations. Revision Date: January 26, 2007 Page 4 of 4 Effective Date: January 26, 2007
