URE-KOTE 1000 - Upload a doc

Read this doc on Scribd: URE-KOTE 1000

PRODUCT DATA SHEET Product: URE-KOTE 1000 Version: November 29, 2007 TECHNICAL DATA DESCRIPTION URE-KOTE 1000 Aliphatic Polyaspartic is a two component 84% solids, low VOC's, aliphatic polyaspartic that was developed for UV stable (colorfast) flooring and coating applications. This new generation polyaspartic displays fast cure times and excellent adhesion characteristics. URE-KOTE 1000 can be spray applied or applied by squeegee and roller at a broad temperature range. This polyaspartic elastomer displays excellent chemical resistance, and UV resistance (in any color) at a wide range of temperatures. URE-KOTE 1000 will provide a smooth glossy finish when fully cured. An aggregate can be broadcast into this self-leveling material to provide a non-skid surface. URE-KOTE 1000 emits very low odor and can be applied indoors without high VOC levels contributed to most polyurethane's. URE-KOTE 1000 meets USDA and FDA specifications. TYPICAL APPLICATIONS ✓ Aircraft Hangar Floors ✓ Manufacturing Floors & Walls ✓ Exterior Floors & Walls ✓ UV-Stable ✓ Showrooms ✓ Commercial Properties ✓ Topcoat for Decorative Finishes FEATURES ✓ Fast Cure Times ✓ ✓ ✓ ✓ ✓ ✓ ✓ Quick Return to Service. Extended Pot Life Minimal waste. Excellent Chemical Resistance Very Low Odor UV Stable (colorfast) Excellent Adhesion USAGE URE-KOTE 1000 adheres well to many substrates when properly primed including concrete, steel and wood. Substrate surfaces should be free of loose particles, rusts, voids and spills. LIMITATIONS (Max thickness per coat: 20 mils) Do not apply URE-KOTE 1000 to wet substrates. Contact LiquidConcrete for primer recommendations in wet applications. In almost every application, a primer is recommended prior to use of the URE-KOTE 1000 polyaspartic. This will help prevent pin holing, and outgassing. NEW CONCRETE The concrete should be allowed to cure for a minimum of 30 days or for concrete that can not be cured for 30 days consult LiquidConcrete for primer. Shot blasting, sandblasting or acid etching (15% muriatic acid / 85% H2O) is required to remove the surface lattice that appeared during the curing process. A primer should be applied to reduce outgassing. Contact LiquidConcrete for specific recommendations. A 10-20 mil coat is generally recommended depending on chemical resistance and abrasion issues. CARBON STEEL The steel must be prepared to a “near white metal,” equivalent to SSPC 10 or NACE 2. For immersion service, a 3-mil blast profile is recommended. A 2-mil blast profile is generally accepted. A 10-20 mil coat of URE-KOTE 1000 is generally recommended based on chemical resistance issues. PROPERTIES Tensile Strength (PSI) ASTM D412……………………………...…………>5000 Tear Strength (PLI) ASTM D2240.......................…………………...........500 Hardness, Shore D ASTM D2240……...……………..……………………..70 Flashpoint (°F) ASTM Pensky-Martin……..…………..……………>200 Taber Abrasion (mg loss) ASTM D4060.....…………………...............................65 CS17-Wheel.....……………...........1 kg per 1000 revs Page 1 of 4 PRODUCT DATA SHEET Product: URE-KOTE 1000 Version: November 29, 2007 Gel Times (75°F)..……...............................20 minutes Tack Free Time (75°F).…..................................1 hour Open to Foot Traffic.......……..………............2 hours Mix Ratio by Volume A / B …………………….Varies Clear = 2:1, most other Colors 2.25:1 - carefully read product labels for specific ratios. CHEMICAL RESISTANCE Consult LiquidConcrete, Inc. Technical Department for specific applications. SHELF LIFE AND STORAGE Six months in factory delivered unopened containers. Keep away from extreme heat, cold, and moisture. Maintain at a proper storage temperature of 60°F - 100°F. STANDARD COLORS All Primary Colors • Custom Tints COVERAGE 80-150 sq ft per gallon @ 10-20 mils PACKAGING 1.5 gallon kit 4.5 gallon kit SHIPPING WEIGHT 10 lbs per gallon (approximate) SHIPPING INFORMATION URE-KOTE 1000 can ship via commercial truck lines. The class is “55” polyaspartic spray. The “A” and “B” sides are unregulated. 2. Cracks greater than 1/6 inch in width shall be routed to a minimum of 1/4 inch wide by 1/4 inch deep and filled with URE-KOTE R-60 or URE-KOTE PF-60 materials. 3. Fill all expansion joints as required – using UREKOTE PF-60. 4. All application equipment shall be in good operating condition. 5. Coating materials shall not be applied when the ambient air temperature or the surface temperature is outside the boundaries as stated on the product data sheets and application guidelines. 6. Keep material out of sun or hot areas prior to applying, as this may cause working time to be diminished and could cause poor appearance and/or adhesion. SURFACE PREPARATION 1. Prepare surface to a minimum CSP-3 profile, removing all surface contaminants, including sealers, oils, or other bond inhibiting substances. Mechanically abrade by shotblaster, diamond grinding, or other means to provide a coarse (rough) texture. 2. Rout out all cracks to a minimum of ½” wide by ½” deep, using concrete saw equipped with dry cut crack chasing blade. 3. Vacuum surface free of all dust and dirt. 4. Fill all routed cracks with LiquidConcrete approved material (recommend URE-KOTE PF-60 or URE-KOTE R-60 depending on conditions). MIXING AND INSTALLATION INSTRUCTIONS Note: please consult product labels for appropriate mixing ratios. Mix no more than can be applied within expected pot life. Replace rollers every hour. If adding pigment: Add pre-measured color pack to resin (part A) and blend for two minutes or until thoroughly and evenly dispersed. INSTALLATION GUIDELINES PRE-OVERLAY CHECKLIST 1. All substrates shall be sound, solid and free from any loose or failing components. Substrates must not flex or deform under load. All surfaces must be free from previously applied coatings, dust, rust, scale, grease, oil, and other bond breaking contaminants. Page 2 of 4 PRODUCT DATA SHEET Product: URE-KOTE 1000 Version: November 29, 2007 For all colors other than Clear, thoroughly mix Part A for 3 minutes using drill equipped with Jiffy mixer to assure even distribution of pigment. This step not required for Clear URE-KOTE 1000 coats. 1. Maintaining proper mixing ratio, pour Parts A and B into a disposable container and mix with jiffy mixer for 2 minutes. 2. Immediately begin application. 3. Apply using roller (high-quality, shed resistant, low-lint, 3/16” or 3/8” nap roller), squeegee, or airless sprayer (max 25 mils WFT per coat minimum 2 hours between each coat). ROLLER APPLICATION Recommended for applications of 10 - 25 mil thicknesses. NOTE: DO NOT pour mixture onto floor and spread - dip and roll only. 1. Dip roller into container of mixed URE-KOTE 1000. 2. Roll onto substrate using high-quality, shed resistant, low-lint, 3/16” or 3/8” nap roller. 3. Replace rollers every hour. SQUEEGEE APPLICATION Recommended for applications of 5 - 10 mil thicknesses, or for topcoats on color quartz and non-skid aggregate applications. NOTE: DO NOT pour entire contents onto floor, only pour small ribbons that can be quickly be squeegeed onto surface. 1. Pour a small amount of mixed URE-KOTE 1000 onto floor. 2. Squeegee onto floor using firm, but even pressure. 3. Clean or replace squeegees frequently. NON-SKID APPLICATIONS Light Duty/Pedestrian Traffic 1. Add 8 fluid ounces of Sole Grip for each gallon of mixed URE-KOTE 1000. 2. Blend thoroughly for 2 minutes using drill equipped with Jiffy mixer to assure even distribution of Sole Grip. 3. Follow ROLLER APPLICATION instructions Heavy Duty/Forklift Traffic 1. Broadcast choice of Unimin, Emery, or White Aluminum Oxide into uncured coating. 2. Wait a minimum of 2 hours before topcoating. 3. Apply additional URE-KOTE 1000 topcoat to lock-in traction aggregate following ROLLER APPLICATION instructions SPRAYER APPLICATION Use conventional airless sprayer similar to that used for latex paint applications. APPLICATION OVER EXISTING EPOXY COATING 1. Clean coating of all dirt, grease, oil or other contaminants by washing with degreaser or soap. 2. Rinse well with fresh water and dry. 3. Sand with sand paper, 36 grit on a floor buffer type sander. 4. Remove dust by vacuum and tack cloth. 5. Apply PRO-SEAL 60 W epoxy primer at 5-10 mils WFT. 6. Allow a minimum of 8 hours max of 24 hours cure. 7. Apply URE-KOTE 1000 at 15-20 mils WFT by roller. REPAIRS AND MAINTENANCE Small repairs to cuts in the coating can be made with URE-KOTE 1000. This material can be caulked or brushed on the surface after scuffing. Re-spraying or rolling of URE-KOTE 1000 (after 4 hours of initial application) requires the use of a primer or sanding to achieve optimum adhesion. CLEAN UP Page 3 of 4 PRODUCT DATA SHEET Product: URE-KOTE 1000 Version: November 29, 2007 1. Clean tools immediately after use with xylene or MEK. MATERIAL SAFETY DATA SHEETS Material safety data sheets are available upon request. It is strongly recommended that all persons involved in the handling of LiquidConcrete, Inc. products read them. WARRANTY NOTICE Recommendations for product use based on tests believed to be reliable. Field conditions vary widely. For this reason, the user must determine product suitability for the particular use and specific applications. LiquidConcrete, Inc. warrants that this product will be free of manufacturing defects for a period of (6) six months from date of manufacture. LiquidConcrete, Inc. will, at its option, replace any material or will refund the purchase price of any material that does not conform to our standard specifications, if the discovery of non-compliance is made within (6) six months of delivery of material. LiquidConcrete, Inc. liability and obligation is limited only to replacement or refund of product. LiquidConcrete, Inc. assumes no liability for injury, loss or damage resulting from use of this product. CORPORATE CONTACT LiquidConcrete, Inc. P.O. Box 16782 Seattle, WA 98116 Tel: 800.201.9300 Fax: 877.349.1922 This e-mail address is being protected from spambots, you need JavaScript enabled to view it www.liquidconcrete.com Page 4 of 4